Indoor PlantsBiophilic DesignCircadian LightingDaily Light Integral
Concept render of the example below: blue-sky Circadian Sky units overhead, and a band of Circadian Sky panels behind the planters. Play the video for a 24-hour time-lapse. The ceiling runs the built-in Circadian Sky program with an 8% night level, and the planter walls run 6000K at 50% from 6 am to 7 pm and 2700K at 5% overnight. The plants open in the morning, sway slowly through the day and fold or droop after the walls dim, following the leaf movements recorded in plant time-lapse studies. Each frame is a 6-second exposure, so people walking through show as streaks. Ray-traced in Blender with each panel's light taken from its IES file.
Architects regularly ask whether Circadian Sky can keep live plants healthy in a space with no windows: an underground passage, an interior atrium, a basement lobby. For the low-light foliage plants that interior landscapers already use, it can. A band of Circadian Sky panels at half output, placed directly behind a planter, gives the foliage 107 to 217 foot-candles over a 12-hour day. That clears the University of Florida maintenance minimums for snake plant, ZZ, pothos and peace lily. Full output roughly doubles it, which brings the back of the bed into the range extension services give for active growth.
This article covers the units plants respond to, what common interior species need, which color temperature gives plants the most light per fixture, and a worked example you can open in Circadian Lab.
How plants measure light
Lux and foot-candles weight light by the sensitivity of the human eye, which peaks in the green. Plants respond to the number of photons between 400 and 700 nm, weighted roughly equally, so horticulture uses two different measures:
PPFD (photosynthetic photon flux density) is the photon rate arriving on a surface, in µmol/m²/s. It plays the role illuminance plays for people.
DLI (daily light integral) is PPFD added up over the day, in mol/m²/day. DLI is what predicts how a plant grows, because a plant under half the light for twice as long receives the same dose. DLI = PPFD × hours × 0.0036.
Converting lux to PPFD depends on the spectrum[10]. From Circadian Sky's measured spectra, 1,000 lux delivers 15.8 µmol/m²/s at 5000K, 15.7 at 6000K, 17.6 at the 40,000K blue-sky setting, and 18.6 at 2200K. So a plant row receiving 100 fc (1,076 lux) at 6000K for 12 hours gets 1,076 × 0.0157 × 12 × 0.0036 = 0.73 mol/m²/day.
What low-light foliage plants need
The most useful interior numbers come from the University of Florida's foliage research center at Apopka, which set maintenance minimums for acclimatized plants indoors[1]. They were measured under cool-white fluorescent light at 12 to 18 hours a day. The DLI column converts each minimum at 6000K over 12 hours.
Species
Maintenance minimum (fc)
DLI at 12 h (mol/m²/day)
Sources
ZZ plant (Zamioculcas)
25 (kept producing new leaves for over a year at 25 fc)
There are two benchmarks, and they sit about ten times apart:
Maintenance (the table) keeps an acclimatized plant looking good with slow or no new growth. UF found that longer hours partly make up for lower intensity, and that continuous 24-hour lighting harmed some species[2].
Active growth for low-light foliage houseplants starts around 3 to 6 mol/m²/day with 12 to 14 hours of light, according to Iowa State Extension[6]. Plants do grow below that: a study of pothos under white LEDs with no daylight saw growth at 0.22 mol/m²/day and faster growth at 1.3[8].
Specify acclimatized stock. Interior foliage plants are produced under 63 to 90% shade, still 1,250 to 3,000 fc, and they drop leaves when moved straight from the nursery into a dim interior[1].
Which color temperature gives plants the most light
Warm settings deliver the most photons per lux, but a tunable fixture also makes less total light at its warm end. Multiplying the two gives the photosynthetic photon flux each Circadian Sky fixture actually produces at each setting. People respond differently: the melanopic (circadian) signal per fixture rises all the way to the 40,000K blue-sky setting.
Per CS24 at full output, as a percentage of each measure's best color temperature. Computed from Circadian Sky measured spectra at 24 color temperatures and Circadian Lab's CCT output factors.
Plants get the most photons per fixture at 4600K, and anything from 4000 to 5000K is within 6% of that. 6000K gives 86%, a fair trade for a cooler, more daylight-like white behind the foliage.
Spectrum. At 6000K the photons split 24% blue, 41% green and 35% red. Cope and Bugbee grew plants under warm, neutral and cool white LEDs and found that at equal photon flux the white types produced similar growth, with more blue giving more compact plants[9]. Circadian Sky holds CRI above 96 from 5000 to 6500K, so leaves read as a natural green to people walking past.
People get the strongest circadian signal from the coolest settings: a melanopic daylight efficacy ratio of 1.39 at 40,000K, against 0.90 at 6000K. Even at 40,000K a fixture still produces 88% of its best plant photon output.
Because the two curves peak in different places, the example below splits the job: blue sky overhead for the people, and a neutral daylight band at plant height for the plants.
Example: planters in a windowless passage
The example is a 100 ft long, 20 ft wide passage segment with a 10 ft ceiling and a raised planter along each wall.
Zone
Fixtures
Mounting
Daytime setting
Ceiling
10 CS24 (2x4), 10 ft on center
Flush in a 10 ft ceiling
40,000K blue sky, 100%
Walls
20 CS24 per side, 5 ft on center
Recessed, landscape, centered 3 ft above the floor
6000K, 50%
Planters
3 ft deep, 18 in high, full length of both walls
Directly in front of the wall panels
Back to front: snake plant, calathea and fern; peace lily and ZZ; trailing pothos
The wall panels sit low enough that the top of each one shows above the foliage and the lower part is behind it. The planting softens the panels for people walking by, and the leaves sit as close to the light as they can get.
What the plants receive
Circadian Lab computed the light on a 6 in grid through the middle 40 ft of a planter, using the CS24 IES file and three interreflection bounces. Foliage light is the average of a leaf facing up and a leaf facing the wall panel.
Daily light integral on the foliage at 12 hours a day. Dot is the median across the row, whisker the 10th to 90th percentile. Dashed lines are the UF maintenance minimums converted to DLI.
At 50% output the rows get 107 fc (front), 127 fc (middle) and 217 fc (back), or 0.8 to 1.6 mol/m²/day. Every row clears the 75 fc minimum, and calathea and fern (150 fc) are met in the back row where they are planted.
At 100% output the light roughly doubles, and the back row reaches 3.1 mol/m²/day, inside the growth band. Start at 50% and step up if new growth stalls.
The wall panels supply about 90% of the light on the foliage. The ceiling units add only 10 to 12 fc at planter height. They are sized for the walkway, which gets about 70 fc.
Gaps between panels are the darkest spots: tight against the wall between two panels the back row falls to about 30 fc. ZZ, with its 25 fc minimum, suits those positions better than snake plant.
Usable growing distance from the wall
Light falls off quickly with distance from the panels. The section below cuts through the planter at a right angle to the wall and shows the foliage DLI at each height and distance, as the median along the row.
Foliage DLI in mol/m²/day at 12 hours a day, wall units at 6000K. The gold bar is the wall panel, 24 to 48 in above the floor. The planter soil is at 18 in.
The brightest zone is the band at panel height within a foot of the wall: 6 in out it gets 2.1 mol/m²/day at 50% output and 4.2 at 100%.
Above the top of the panel the light drops fast, so tall plants such as snake plant get most of their light on the lower half of the leaves.
At 100% output the foliage between 24 and 48 in high gets 1.1 to 1.3 mol/m²/day (about 150 fc) all the way to the front edge of the planter. At 50% the front half of the planter gets 0.65 to 1.1.
The next chart turns the section into a planting depth for each setting: how far from the wall the foliage at panel height keeps at least 1.1 mol/m²/day, the level calathea and fern need, and at least 3 mol/m²/day, the bottom of the growth band.
Distance from the wall where foliage 36 in above the floor gets at least 1.1 mol/m²/day (solid) or 3 mol/m²/day (dashed) at 12 hours a day, median along the row.
At 50% output plants that need 150 fc belong within about 18 in of the wall. At 100% they can go 3 to 4 ft out.
Growth-level light of 3 mol/m²/day reaches up to about a foot from the wall, and only at 75% output and above.
Color temperature moves the depth by a few inches. 4000K and 5000K reach about 15% farther than 6000K, and 6500K about 5 to 8% less. The 6000K setting gives up a little depth for a cooler look next to the 40,000K ceiling.
The model does not include leaves shading each other. A dense real canopy gets less light toward the back of the bed, so treat the back-row figures as upper bounds.
Strong circadian signal for people; most plant light per fixture near neutral white
Evening
Built-in program warms and dims
Same as day until the photoperiod ends
Supports sleep timing for people; plants complete their 12 to 14 h
Night, if the space stays open
Warm and dim
Off, or 2700K at 10% or less for appearance
Plants need a dark period; continuous light harms some species
The time-lapse at the top of this article shows this schedule over one day.
Higher output on the wall panels also raises their glare for people walking past, so dense planting in front of them matters more as the output goes up.
Which plants this suits
These numbers cover the low-light foliage palette that interior landscapers use for lobbies and offices. High-light plants such as most succulents, flowering plants and vegetables need several times more light, which means more panels, closer spacing or a dedicated grow light. Circadian Lab can model any of those layouts the same way.
Circadian Sky figures come from Innerscene's measured spectra (24 color temperatures), the CS24-75W IES file and the Circadian Lab photometric engine. Plant models in the renders: snake plant by digitalurban and ModellingInProgress, pothos by AllQuad, peace lily by RafaelBR873D and aqpetteri (Sketchfab, CC BY 4.0); calathea and fern from Poly Haven (CC0).